Everyone fascinates about hacking a remote computer. You would like to hack a remote computer of your friend, boyfriend or a girlfriend in order to find out their secrets. You would think about using a browser to accomplish the task. But it is not the right process. Here I will tell about using a command prompt for this process.
NOTE --> 1 : The remote computer must be online i.e. the computer you want to hack must be switched on and connected to the internet.
2 : Firewall of remote computer must be off. This is because firewall prevents accessing a remote computer from an unauthenticated network.
The following processes should be adopted in sequence to hack a remote computer -->
1 : Go to Start>Run. Type cmd and then click OK. This will open command prompt.
2 : Change the directory. type cd C:\WINDOWS\ at command prompt. This is necessary as the commands required after this requires this to be done.
3 : Type ping ip-address at command prompt. This commandchecks whether the remote computer is online or not.
4 : In order to gain access to target computer it is necessary to check for open vulnerable ports. These ports are actually virtual ports where different softwares are brunning. To scan for these ports use a port scanner. E.g. port 21 denotes ftp, port 25 for SMTP and port 80 for HTTP.
5 : Type telnet ip-address port-number at command prompt. This will connect you to the remote computer.
6 : After connection you will be asked for username and password for user authentication. You can guess the password using Brute-force software which generates password for you. This will allow you to enter into remote system.
7 : Create a new Network Drive whose drive letter path is different from that is used by your own hard disk-drives, CD/DVD drives or Flash drives.
8 : Now you can copy or view files of remote system through that network drive without the knowledge of others.
WARNING --> This is only for educational purposes and not for causing any harm to others. It is completely discouraged to do so. I am not all responsible for any hindrance or any criminal activities carried out by you using this.
NOTE --> 1 : The remote computer must be online i.e. the computer you want to hack must be switched on and connected to the internet.
2 : Firewall of remote computer must be off. This is because firewall prevents accessing a remote computer from an unauthenticated network.
The following processes should be adopted in sequence to hack a remote computer -->
1 : Go to Start>Run. Type cmd and then click OK. This will open command prompt.
2 : Change the directory. type cd C:\WINDOWS\ at command prompt. This is necessary as the commands required after this requires this to be done.
3 : Type ping ip-address at command prompt. This commandchecks whether the remote computer is online or not.
4 : In order to gain access to target computer it is necessary to check for open vulnerable ports. These ports are actually virtual ports where different softwares are brunning. To scan for these ports use a port scanner. E.g. port 21 denotes ftp, port 25 for SMTP and port 80 for HTTP.
5 : Type telnet ip-address port-number at command prompt. This will connect you to the remote computer.
6 : After connection you will be asked for username and password for user authentication. You can guess the password using Brute-force software which generates password for you. This will allow you to enter into remote system.
7 : Create a new Network Drive whose drive letter path is different from that is used by your own hard disk-drives, CD/DVD drives or Flash drives.
8 : Now you can copy or view files of remote system through that network drive without the knowledge of others.
WARNING --> This is only for educational purposes and not for causing any harm to others. It is completely discouraged to do so. I am not all responsible for any hindrance or any criminal activities carried out by you using this.
Looks fine..........would have been better with a video or screenshots:-)
ReplyDeleteI tried this method with WindowsXp as my OS. But when I posted this and even now also I am q LINUX user so it is not possible to provide screenshots.
DeleteWILL IT WORK??
ReplyDeleteIt worked fine on WindowsXP.
Deletehow to get telnet password of remote computer???
ReplyDeleteit is showing that telnet is not recognize as external or internal command
ReplyDeletewaht to do
m using windows 7
how to turn off firewall of others' computer will u please tell
ReplyDelete